Leading 10 usual forklift crashes ， forklift procedure must take notice of these issues ！.

Do not take too lightly the forklift at work. If the operation is not good, there will certainly be major mishaps in mins, and there are many mishaps entailing forklifts.

Situation 1: The forklift freight obstructed the motorist's view, and the person in front might not be found, causing a rolling mishap.
Situation 2: In order to preserve the equilibrium of the forklift when raising hefty products, the employees used their body weight as the weight, which almost caused casualties.
Instance 3: The size of the forklift freight exceeds the permitted size of the route and holds on the roadside rack, which nearly creates an crash.
Case 4: Forklift is speeding and rolls over throughout a turn.
Instance 5: The forklift vehicle driver did not notice the pedestrian, and the pedestrian did not notice the forklift.
Case 6: The forklift raises the personnel unlawfully, the forklift vehicle driver does not put on the seat belt, the forklift lifter drops and the vehicle driver is squashed when the forklift rolls over.
Situation 7: The forklift driver did not use a safety belt and fell from the car when it rolled over and was crushed.
Forklift procedure ought to pay attention to these matters ：.

Beginning.
1. Prior to beginning, observe the environments, and after confirming that there are no barriers that prevent the safety of driving, beep the horn initially and after that begin.
2. For cars with hydraulic (air pressure) brakes, the brake hydraulic pressure (air pressure) scale have to be secure prior to beginning.
3. When the forklift begins with a tons, the driver should initially validate that the load is stable and reliable.
4. The beginning needs to be slow and consistent.

Driving.
1. When driving, the height between the bottom end of the fork and the ground need to be maintained 300mm-400mm, and the mast needs to be slanted backward. .
2. Do not raise the fork expensive when driving. When going into and leaving the job site or while driving, take care that there will be no challenges overhead. When the load is traveling, the fork needs to not be raised too high, which will influence the security of the forklift. .
3. After unloading, the fork must be lowered to the typical driving placement prior to driving. .
4. When turning, if there are pedestrians or cars close by, the driving signal must be provided initially. High-speed doglegs are prohibited. High-speed sharp turns will certainly create the car to lose lateral stability and topple. .
5. When the forklift is downhill, it is strictly forbidden to shut off the fire and slide, and it is forbidden to brake instantly while driving with tons unless there are unique situations.
6. When the forklift is running, it has to obey the web traffic rules in the manufacturing facility and have to maintain a certain safety distance from the car in front. .
7. When the forklift is running, the tons should be in the lowest setting that does not impede the driving, and the gantry ought to be appropriately slanted back. The tons shall not be increased except when stacking or loading. .
8. The height of the lots must not obstruct the vehicle driver's view. In unique scenarios, when the product impacts the forward vision, drive at a low speed when reversing.
9. It is restricted to activate the ramp, neither to drive across the ramp. .
10. The safe driving speed of the forklift in the manufacturing facility location is 5 km/h, and it needs to drive safely at a low rate when getting in the manufacturing workshop area. .
11. When the forklift is raised, raised or driven, it is prohibited for workers to stand on the fork to hold things and play a stabilizing function. .
12. If problems are found, they will certainly be repaired and reported in a timely fashion, and they will never run with health problems or conceal them.

filling and dumping.
1. When fork-loading products, the range in between the two forks need to be changed as needed to make the lots of the two forks balanced and not manipulated, and one side of the item need to protest the rack. .
2. It is restricted to collaborate with a single fork or make use of a fork top or pull. In unique situations, safety indication must be established to remind bordering pedestrians. .
3. In the process of loading and dumping items, the forklift has to be braked with the brake. .
4. The rate of the car need to be sluggish and steady. Beware not to roll the wheels on the dunnage, so as not to stretch the rolled items and injure people. .
5. When making use of a fork to fork the goods, the fork should be as deep as feasible under the load, and it must be kept in mind that the fork tip must not touch other products or things. The load must be stabilized with marginal back tilt of the gantry so that the tons does not glide backwards. The mast can be slanted onward slightly when the tons is decreased to allow for simple positioning of the lots and extraction of the forks. .
6. It is prohibited to fork products at broadband and collide with hard items with the fork head. .
7. When the forklift is functioning, it is restricted for people to stand around the fork, so as to prevent the collapse of the goods and injure individuals. .
8. Overloading is restricted, and it is forbidden to make use of forks to raise personnel to engage in high-altitude operations to prevent high-altitude dropping crashes. .
9. It is not permitted to make use of the brake inertia to slip, put, round or roll objects. .
10. It is not allowed to utilize forks to choose, turn pallet discharge.

Leaving .
1. It is prohibited to leave the forklift when the Stand-on Electric Pallet Stacker products on the fork impend. Prior to leaving the forklift, you need to dump the goods or reduced the fork structure.
2. Draw the hand brake take care of to dead or dispirit the hand brake button.
3. The engine is switched off and the power is removed. (Except for special scenarios, such as the motorist does not leave the automobile's line of vision and does not surpass 1 minute).
4. Eliminate the key. .

Forklift Operation Precautions.
1. Before and after the forklift operation, the look needs to be examined, and gas, lubricating oil and cooling water should be included.
2. Examine the safety and security efficiency of starting, running and braking.
3. Examine whether the lights and horn signals are full and efficient.
4. During the operation of the forklift, examine whether the stress and temperature are normal.
5. After the forklift is running, the exterior leak must also be checked and the seals need to be changed in time.

Forklift Safety Operation Specifications.
1. You should check prior to leaving the cars and truck;.
2. When you come across someone before you throughout driving, you should send out a signal at a distance of 5 m;.
3. The driving speed in the factory does not go beyond 5 km/h;.
4. When driving, the low point of the freight must be 0.3 m ~ 0.4 m Stand-on Electric Pallet Stacker above the ground;.
5. The transforming must not be too sharp to stop the tendency of "free switching";.
6. Running up and down the incline ought to be slow-moving and uniform, and no activating the incline is allowed.
7. Do not drive throughout the gradient. When the slope is greater than 10%, the automobile ought to be driven in reverse when going downhill;.
8. When the forklift employees carry the goods and move on, if they encounter big or hefty products and most likely to the chauffeur's view, they ought to take the turning around exercise
.
The "Eight Prohibitions" must be adhered to in the operation.
1. Solitary fork operation is not enabled.
2. It is not permitted to lift the goods for far away driving.
3. It is not permitted to pick up the goods by handing over the pallet with the fork.
4. It is not permitted to directly shovel chemicals, flammables and various other unsafe chemicals with forks.
5. It is not allowed to utilize inertia pressure to pick up the goods.
6. It is not enabled to make use of braking force to exile round or easy-to-roll things.
7. It is not allowed to bring people to service the pallet or fork, and it is purely restricted to stand under the fork after the fork is raised.
8. Do not drive laterally on inclines
.
Parking is not permitted under the list below problems.
1. Contours, slim roadways, railway crossings;.
2. Sections with a longitudinal slope above 5%.
3. When there is an barrier on one side of the roadway, the contrary side of the area with the same length as the obstacle ought to be within 20 meters at each end.

Web：https://www.onenforklifts.com/
Email：[email protected]
Phone：+86 13827083844